What is the name of communication system that connects two or more computers?

1. Bus Topology: Every computer and network device is connected to a single cable in a bus topology network. Linear Bus topology is defined as having exactly two terminals.

Advantages

• Installation is simple.
• Compared to mesh, star, and tree topologies, the bus utilizes less cabling.

Disadvantages

• Difficulty in reconfiguring and isolating faults.
• A bus cable malfunction or break interrupts all communication.

2. Ring Topology: The topology is named ring topology because one computer is connected to another, with the final one being connected to the first. Exactly two neighbors for each device. A signal is passed along the ring in one direction. Each ring incorporates a repeater. 

Advantages

• Data transmission is relatively straightforward because packets only move in one direction.
• There is no requirement for a central controller to manage communication between nodes.
• Easy installation & Reconfiguration
• Simplified Faulty connections

Disadvantages

• In a Unidirectional Ring, a data packet must traverse through all nodes.
• All computers must be turned on in order for them to connect with one another.

3. Star Topology: Each device in a star topology has a dedicated point-to-point link to a central controller, which is commonly referred to as the HUB. There is no direct connection between the devices. Traffic between the devices is not allowed in this topology. As an exchange, the controller is used.

Advantages

• When attaching or disconnecting devices, there are no network interruptions.
• It’s simple to set up and configure.
• Identifying and isolating faults is simple.
• Less Expensive than mesh 
• Easy to install & configure

Disadvantages

• Nodes attached to the hub, switch, or concentrator is failed if they fail.
• Because of the expense of the hubs, it is more expensive than linear bus topologies.
• More cable required compared to bus or ring 
• Too much dependency on Hub

  Example: Used in high-speed LANs

4. Mesh Topology: Every device in a mesh topology has dedicated point-to-point connectivity to every other device. The term “dedicated” refers to the fact that the link exclusively transports data between the two devices it links. To connect n devices, a fully connected mesh network contains n *(n-1)/2 physical channels.

Advantages

• Data can be sent from multiple devices at the same time. This topology can handle a lot of traffic.
• Even if one of the connections fails, a backup is always available. As a result, data transit is unaffected.
• Physical boundaries prevent other users from gaining access to messages
• Point to Point links make fault transmission & fault isolation easy 

Disadvantages

• The amount of cabling and the number of I/O ports that are necessary.
• The sheer bulk of wiring can be greater than the available space can accommodate.
• It is difficult to install and reconfigure.

     Example:  connection of telephone regional office in which each regional office needs to be connected to every other regional office. 

5. Tree Topology: The topology of a tree is similar to that of a star. Nodes in a tree, like those in a star, are connected to a central hub that manages network traffic. It has a root node, which is connected to all other nodes, producing a hierarchy. Hierarchical topology is another name for it. The number of Star networks is connected via Bus in Tree Topology.

Advantages

• Network expansion is both possible and simple.
• We partition the entire network into pieces (star networks) that are easier to manage and maintain.
• Other segments are unaffected if one segment is damaged.

Disadvantages

• Tree topology relies largely on the main bus cable because of its basic structure, and if it fails, the entire network is handicapped.
• Maintenance becomes more challenging when more nodes and segments are added.

Networking Devices 

Basic hardware interconnecting network nodes, such as Network Interface Cards (NICs), Bridges, Hubs, Switches, and Routers, are used in all networks. In addition, a mechanism for connecting these building parts is necessary, which is usually galvanic cable and optical cable are less popular (“optical fiber”)The following are the network devices :

• NIC (Network Interface Card): A network card, often known as a network adapter or NIC (network interface card), is computer hardware that enables computers to communicate via a network. It offers physical access to networking media and, in many cases, MAC addresses serve as a low-level addressing scheme. Each network interface card has a distinct identifier. This is stored on a chip that is attached to the card.
• Repeater: A repeater is an electrical device that receives a signal, cleans it of unwanted noise, regenerates it, and retransmits it at a higher power level or to the opposite side of an obstruction, allowing the signal to travel greater distances without degradation. In the majority of twisted pair Ethernet networks, Repeaters are necessary for cable lengths longer than 100 meters in some systems. Repeaters are based on physics.
• Hub: A hub is a device that joins together many twisted pairs or fiber optic Ethernet devices to give the illusion as a formation of a single network segment. The device can be visualized as a multiport repeater. A network hub is a relatively simple broadcast device. Any packet entering any port is regenerated and broadcast out on all other ports, and hubs do not control any of the traffic that passes through them. Packet collisions occur as a result of every packet being sent out through all other ports, substantially impeding the smooth flow of communication.
• Bridges: Bridges broadcast data to all the ports but not on the one that received the transmission. Bridges, on the other hand, learn which MAC addresses are reachable through specific ports rather than copying messages to all ports as hubs do. Once a port and an address are associated, the bridge will only transport traffic for that address to that port.
• Switches: A switch differs from a hub in that it only forwards frames to the ports that are participating in the communication, rather than all of the ports that are connected. The collision domain is broken by a switch, yet the switch depicts itself as a broadcast domain. Frame forwarding decisions are made by switches based on MAC addresses.
• Routers: Routers are networking devices that use headers and forwarding tables to find the optimal way to forward data packets between networks. A router is a computer networking device that links two or more computer networks and selectively exchanges data packets between them. A router can use address information in each data packet to determine if the source and destination are on the same network or if the data packet has to be transported between networks. When numerous routers are deployed in a wide collection of interconnected networks, the routers share target system addresses so that each router can develop a table displaying the preferred pathways between any two systems on the associated networks.
• Gateways: To provide system compatibility, a gateway may contain devices such as protocol translators, impedance matching devices, rate converters, fault isolators, or signal translators. It also necessitates the development of administrative procedures that are acceptable to both networks. By completing the necessary protocol conversions, a protocol translation/mapping gateway joins networks that use distinct network protocol technologies.

Internet 

The internet is a larger network that allows computer networks controlled by enterprises, governments, colleges, and other organizations all over the world to communicate with one another. As a result, there are a tangle of cables, computers, data centers, routers, servers, repeaters, satellites, and wi-fi towers that allow digital data to go around the world.

The Internet is a vast network of networks that functions as a networking infrastructure. It links millions of computers throughout the world, creating a network in which any computer can talk with any other computer as long as they are both linked to the Internet.

The Internet is a global network of interconnected computers that communicate and share information using a standardized Internet Protocol Suite.

Sample Questions

Question 1: List the advantages and disadvantages of the internet.

Solution:

Advantages of internet are,

• Source of entertainment – Online gaming, talking, browsing, music, movies, dramas, and TV series are quickly becoming the most popular ways to pass the time.
• Source of information – There is no better place to conduct research than the internet. We can learn about the latest trends, communicate with experts without having to physically visit them, and seek professional advice over the internet.
• E – Commerce – With the advancement of internet technology, large online E-commerce enterprises such as Amazon, Ali Baba, myntra etc. have emerged.
• Working from home, collaborating with others, and having access to a global workforce are all advantages.
• Keeps Updated – Because there are hundreds of thousands of newsgroups and services that keep you updated with every tick of the clock, the Internet is a source of the most recent news.

Disadvantages of internet are,

• Time Wastage – Most people believe that spending too much time on the internet is unhealthy for young people and leads to obesity. 
• Money Laundering – Aside from reputable sites, there are some Social Media Advertising sites that try to steal your personal information, credit card information, and even your pin code. You can easily become a victim of money scam if they get this information.
• Exposure to private data – It is now quite easy to decipher someone’s chat or email communication thanks to the hacking community. As we all know, data is transmitted in packets, which hackers can simply detect and reconstruct.
• Harassment & threatening – Bullies exist online, just as they do in real life, and they can lower your self-esteem by harassing and threatening you. Some of these individuals may be persons who are aware of some of your personal details and dislike you, and may use this information to harass you.

Question 2: List the ways to connect to the internet.

Solution:

We can connect to the internet in the following ways:

• Dial-Up – In order to access the Internet, in this type of connection, users must connect their phone line to a computer . This link prevents the user from using tier home phone service to make or receive calls.
• Broadband – Broadband is a high-speed internet connection that is frequently utilized nowadays and is provided by cable or phone companies.
• Wireless connections – Internet access is accomplished by radio waves, thus it is possible to connect to the Internet from any location. Wi-Fi and mobile service providers are examples of wireless connections.

Question 3: Compare the Internet & the World Wide Web

Solution:

Sir Tim Berners-Lee is credited with creating the World Wide Web. He came up with the core idea for the WWW while working at the European Organization for Nuclear Research in 1989. He wanted to combine the growing technologies of computers, data networks, and hypertext into a powerful and easy-to-use worldwide information system.

The Internet is a vast network of networks that functions as a networking infrastructure. It links millions of computers throughout the world, creating a network in which any computer can talk with any other computer as long as they are both linked to the Internet. The World Wide Web, or simply Web, is a method of gaining access to information over the Internet.

The World Wide Web, also known as the ‘www,’ is a collection of webpages that can be quickly published on the Internet and read by millions of people.

Question 4: What is the full form of www?

Solution:

The full form of www is World Wide Web. It is the world’s most dominant software and is commonly known as the web.

What is the name of a communication system that connects two or more computers?

A Local Area Network (LAN) connects two or more computers together via Ethernet cables. For office networking, this is one of the most common network types, because of its reliability, stability and performance.

What is used to connect two or more computers?

Routers are general-purpose devices that interconnect two or more heterogeneous networks. They are usually dedicated to special-purpose computers, with separate input and output network interfaces for each connected network.